DDR V1.09 a930779e06 typ 22/11/21-17:50:56 LPDDR4, 2112MHz channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB Manufacturer ID:0xff CH0 RX Vref:29.7%, TX Vref:12.2%,12.2% CH1 RX Vref:30.7%, TX Vref:13.2%,13.2% CH2 RX Vref:29.7%, TX Vref:12.2%,12.2% CH3 RX Vref:29.7%, TX Vref:12.2%,12.2% change to F1: 528MHz change to F2: 1068MHz change to F3: 1560MHz change to F0: 2112MHz out U-Boot SPL board init U-Boot SPL 2017.09-gc060f28d70-220414 #zyf (Apr 18 2022 - 18:13:34) Failed to set cpub01 Failed to set cpub23 unknown raw ID phN unrecognized JEDEC id bytes: 00, 00, 00 Trying to boot from MMC2 part_get_info_efi: *** ERROR: Invalid GPT *** GUID Partition Table Header signature is wrong: 0xX != 0xX part_get_info_efi: *** ERROR: Invalid Backup GPT *** part_get_info_efi: *** ERROR: Invalid GPT *** GUID Partition Table Header signature is wrong: 0xX != 0xX part_get_info_efi: *** ERROR: Invalid Backup GPT *** spl: partition error Trying fit image at 0x4000 sector Not fit magic Trying fit image at 0x5000 sector Not fit magic Trying to boot from MMC1 Trying fit image at 0x4000 sector ## Verified-boot: 0 ## Checking atf-1 0x00040000 ... sha256(bb1bbbc832...) + OK ## Checking uboot 0x00200000 ... sha256(47cdbd8daf...) + OK ## Checking fdt 0x0035d990 ... sha256(c07f4a4d71...) + OK ## Checking atf-2 0x000f0000 ... sha256(30812190d0...) + OK ## Checking atf-3 0xff100000 ... sha256(cb7bdbec2b...) + OK ## Checking optee 0x08400000 ... sha256(fde0860845...) + OK Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000) Total: 333.302 ms INFO: Preloader serial: 2 NOTICE: BL31: v2.3():v2.3-499-ge63a16361:derrick.huang NOTICE: BL31: Built : 10:58:38, Jan 10 2023 INFO: spec: 0xa INFO: ext 32k is not valid INFO: ddr: stride-en 4CH INFO: GICv3 without legacy support detected. INFO: ARM GICv3 driver initialized in EL3 INFO: valid_cpu_msk=0xff bcore0_rst = 0x0, bcore1_rst = 0x0 INFO: system boots from cpu-hwid-0 INFO: idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001 INFO: dfs DDR fsp_params[0].freq_mhz= 2112MHz INFO: dfs DDR fsp_params[1].freq_mhz= 528MHz INFO: dfs DDR fsp_params[2].freq_mhz= 1068MHz INFO: dfs DDR fsp_params[3].freq_mhz= 1560MHz INFO: BL31: Initialising Exception Handling Framework INFO: BL31: Initializing runtime services INFO: BL31: Initializing BL32 INFO: hdmirx_handler: dma not on, ret I/TC: I/TC: OP-TEE version: 3.13.0-652-g4542e1efd #derrick.huang (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #5 2022骞09鏈20鏃鏄熸湡浜09:41:09 CST aarch64 I/TC: Primary CPU initializing I/TC: Primary CPU switching to normal world boot INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x200000 INFO: SPSR = 0x3c9 U-Boot 2017.09(u-boot commit id: 0c26676955)(sdk version: rk3588_linux_release_20230114_v1.0.6c)-g0c26676955 #lvsx (Jan 29 2023 - 14:45:41 +0800) Model: Rockchip RK3588 Evaluation Board PreSerial: 2, raw, 0xfeb50000 DRAM: 8 GiB Sysmem: init Relocation Offset: eda19000 Relocation fdt: eb9fa658 - eb9fecc8 CR: M/C/I Using default environment mmc@fe2c0000: 1, mmc@fe2e0000: 0 Bootdev(atags): mmc 0 MMC0: HS200, 200Mhz PartType: EFI DM: v2 boot mode: None ** Unrecognized filesystem type ** Found DTB in boot part DTB: rk-kernel.dtb HASH(c): OK I2c0 speed: 100000Hz vsel-gpios- not found! en-gpios- not found! vdd_cpu_big0_s0 800000 uV vsel-gpios- not found! en-gpios- not found! vdd_cpu_big1_s0 800000 uV I2c1 speed: 100000Hz vsel-gpios- not found! en-gpios- not found! vdd_npu_s0 800000 uV spi2: RK806: 2 ON=0x00, OFF=0x00 vdd_gpu_s0 750000 uV vdd_cpu_lit_s0 750000 uV vdd_log_s0 750000 uV vdd_vdenc_s0 init 750000 uV vdd_ddr_s0 850000 uV get vp0 plane mask:0x5, primary id:2, cursor_plane:-1, from dts get vp1 plane mask:0xa, primary id:3, cursor_plane:-1, from dts get vp2 plane mask:0x140, primary id:8, cursor_plane:-1, from dts get vp3 plane mask:0x280, primary id:9, cursor_plane:-1, from dts Could not find baseparameter partition Model: Firefly AIO-3588Q MIPI101(Linux) Rockchip UBOOT DRM driver version: v1.0.1 vp0 have layer nr:2[0 2 ], primary plane: 2 vp1 have layer nr:2[1 3 ], primary plane: 3 vp2 have layer nr:2[6 8 ], primary plane: 8 vp3 have layer nr:2[7 9 ], primary plane: 9 Using display timing dts dsi@fde20000: detailed mode clock 72600 kHz, flags[a] H: 0800 0832 0846 0872 V: 1280 1360 1368 1388 bus_format: 100e VOP update mode to: 800x1280p60, type: MIPI0 for VP3 [list]p_rate=1188000000, best_rate=69882352, div=17, sel=0 [list]p_rate=1500000000, best_rate=71428571, div=21, sel=1 [list]p_rate=0, best_rate=71428571, div=21, sel=1 [list]p_rate=786431991, best_rate=71493817, div=11, sel=3 [result]p_rate=786431991, best_rate=71493817, div=11, sel=3 VP3 set crtc_clock to 71493KHz VOP VP3 enable Esmart3[500x501->500x501@150x389] fmt[2] addr[0xedf20000] final DSI-Link bandwidth: 476620 Kbps x 4 command interface is busy: 0x10001 [Firefly]-[rockchip_panel_send_dsi_cmds]-[265]: read 4 = 0 [Firefly]-[rockchip_panel_send_dsi_cmds]-[270]: Not Found ID = 83 MIPI! failed to write/read cmd0: -999 failed to send on cmds: -999 aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout aux timeout dw-dp: Too many retries, giving up. First error: -110 failed to probe DP link: -110 aux timeout dw-dp: transaction timed out aux timeout dw-dp: transaction timed out aux timeout dw-dp: transaction timed out aux timeout dw-dp: transaction timed out aux timeout dw-dp: transaction timed out aux timeout dw-dp: transaction timed out aux timeout dw-dp: transaction timed out aux timeout dw-dp: transaction timed out aux timeout dw-dp: transaction timed out aux timeout dw-dp: transaction timed out can't get edid block:0 failed to get edid dp@fde60000: detailed mode clock 0 kHz, flags[0] H: 0000 0000 0000 0000 V: 0000 0000 0000 0000 bus_format: 0 VOP update mode to: 0x0p0, type: DP1 for VP2 DP dclk_core out of range(max_dclk: 600000 KHZ, dclk_core: 0 KHZ) VP2 set crtc_clock to 0KHz ERROR: VP2: unsupported display timing CLK: (uboot. arm: enter 1008000 KHz, init 1008000 KHz, kernel 0N/A) b0pll 24000 KHz b1pll 24000 KHz lpll 24000 KHz v0pll 0 KHz aupll 786431 KHz cpll 1500000 KHz gpll 1188000 KHz npll 850000 KHz ppll 1100000 KHz aclk_center_root 702000 KHz pclk_center_root 100000 KHz hclk_center_root 396000 KHz aclk_center_low_root 500000 KHz aclk_top_root 594000 KHz pclk_top_root 100000 KHz aclk_low_top_root 396000 KHz Net: eth0: ethernet@fe1b0000, eth1: ethernet@fe1c0000 Hit key to stop autoboot('CTRL+C'): 0 ANDROID: reboot reason: "(none)" optee api revision: 2.0 TEEC: Waring: Could not find security partition Not AVB images, AVB skip ANDROID: Hash OK Booting IMAGE kernel at 0x00400000 with fdt at 0x08300000... Fdt Ramdisk skip relocation ## Booting Android Image at 0x003ff800 ... Kernel: 0x00400000 - 0x02c0c200 (41009 KiB) ramdisk: 0x0a200000 - 0x0aace3aa (9017 KiB) ## Flattened Device Tree blob at 0x08300000 Booting using the fdt blob at 0x08300000 XIP Kernel Image from 0x00400000 to 0x00400000 ... OK kernel loaded at 0x00400000, end = 0x02c0c200 'reserved-memory' cma: addr=10000000 size=10000000 'reserved-memory' ramoops@110000: addr=110000 size=f0000 Using Device Tree in place at 0000000008300000, end 000000000832c29b Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000) Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000) Adding bank: 0x100000000 - 0x200000000 (size: 0x100000000) Adding bank: 0x2f0000000 - 0x300000000 (size: 0x10000000) Total: 1222.288 ms Starting kernel ... [ 1.968773] Booting Linux on physical CPU 0x0000000000 [0x412fd050] [ 1.968797] Linux version 5.10.110 (root@ubuntu) (kernel commit id: 8b4c629a78e2) (sdk version: rk3588_linux_release_20230301_v1.0.6e) (aarch64-none-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 10.3.1 20210621, GNU ld (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 2.36.1.20210621) #1 SMP Fri Mar 31 16:14:22 CST 2023 [ 1.976160] Machine model: Firefly AIO-3588Q MIPI101(Linux) [ 1.976252] earlycon: uart8250 at MMIO32 0x00000000feb50000 (options '') [ 1.981026] printk: bootconsole [uart8250] enabled [ 1.983188] efi: UEFI not found. [ 1.987409] OF: fdt: Reserved memory: failed to reserve memory for node 'drm-cubic-lut@00000000': base 0x0000000000000000, size 0 MiB [ 1.988558] Reserved memory: created CMA memory pool at 0x0000000010000000, size 256 MiB [ 1.989301] OF: reserved mem: initialized node cma, compatible id shared-dma-pool [ 2.102122] Zone ranges: [ 2.102362] DMA [mem 0x0000000000200000-0x00000000ffffffff] [ 2.102933] DMA32 empty [ 2.103201] Normal [mem 0x0000000100000000-0x00000002ffffffff] [ 2.103769] Movable zone start for each node [ 2.104161] Early memory node ranges [ 2.104491] node 0: [mem 0x0000000000200000-0x00000000083fffff] [ 2.105068] node 0: [mem 0x0000000009400000-0x00000000efffffff] [ 2.105645] node 0: [mem 0x0000000100000000-0x00000001ffffffff] [ 2.106222] node 0: [mem 0x00000002f0000000-0x00000002ffffffff] [ 2.106797] Initmem setup node 0 [mem 0x0000000000200000-0x00000002ffffffff] [ 2.151335] psci: probing for conduit method from DT. [ 2.151807] psci: PSCIv1.1 detected in firmware. [ 2.152231] psci: Using standard PSCI v0.2 function IDs [ 2.152712] psci: Trusted OS migration not required [ 2.153163] psci: SMC Calling Convention v1.2 [ 2.153933] percpu: Embedded 32 pages/cpu s93288 r8192 d29592 u131072 [ 2.154724] Detected VIPT I-cache on CPU0 [ 2.155127] CPU features: detected: GIC system register CPU interface [ 2.155718] CPU features: detected: Virtualization Host Extensions [ 2.156290] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 2.156936] alternatives: patching kernel code [ 2.159380] Built 1 zonelists, mobility grouping on. Total pages: 2059848 [ 2.160017] Kernel command line: storagemedia=emmc androidboot.storagemedia=emmc androidboot.mode=normal dsi-0=2 storagenode=/mmc@fe2e0000 androidboot.verifiedbootstate=orange androidboot.serialno=94544b1d1f1920d3 ro rootwait earlycon=uart8250,mmio32,0xfeb50000 console=ttyFIQ0 irqchip.gicv3_pseudo_nmi=0 root=PARTLABEL=rootfs rootfstype=ext4 overlayroot=device:dev=PARTLABEL=userdata,fstype=ext4,mkfs=1 coherent_pool=1m systemd.gpt_auto=0 cgroup_enable=memory swapaccount=1 [ 2.164876] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [ 2.165979] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) [ 2.166699] mem auto-init: stack:off, heap alloc:off, heap free:off [ 2.173202] software IO TLB: mapped [mem 0x00000000e9f00000-0x00000000edf00000] (64MB) [ 2.236108] Memory: 7828320K/8370176K available (22464K kernel code, 3824K rwdata, 6956K rodata, 7616K init, 673K bss, 279712K reserved, 262144K cma-reserved) [ 2.237518] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 2.238144] ftrace: allocating 67815 entries in 265 pages [ 2.332275] ftrace: allocated 265 pages with 3 groups [ 2.332987] rcu: Hierarchical RCU implementation. [ 2.333423] rcu: RCU event tracing is enabled. [ 2.333839] Rude variant of Tasks RCU enabled. [ 2.334255] Tracing variant of Tasks RCU enabled. [ 2.334696] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies. [ 2.340397] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 2.342661] GICv3: GIC: Using split EOI/Deactivate mode [ 2.343145] GICv3: 480 SPIs implemented [ 2.343499] GICv3: 0 Extended SPIs implemented [ 2.343927] GICv3: Distributor has no Range Selector support [ 2.344451] GICv3: 16 PPIs implemented [ 2.344835] GICv3: CPU0: found redistributor 0 region 0:0x00000000fe680000 [ 2.345562] ITS [mem 0xfe640000-0xfe65ffff] [ 2.345987] ITS@0x00000000fe640000: allocated 8192 Devices @100220000 (indirect, esz 8, psz 64K, shr 0) [ 2.346864] ITS@0x00000000fe640000: allocated 32768 Interrupt Collections @100230000 (flat, esz 2, psz 64K, shr 0) [ 2.347815] ITS: using cache flushing for cmd queue [ 2.348290] ITS [mem 0xfe660000-0xfe67ffff] [ 2.348710] ITS@0x00000000fe660000: allocated 8192 Devices @100250000 (indirect, esz 8, psz 64K, shr 0) [ 2.349588] ITS@0x00000000fe660000: allocated 32768 Interrupt Collections @100260000 (flat, esz 2, psz 64K, shr 0) [ 2.350537] ITS: using cache flushing for cmd queue [ 2.351100] GICv3: using LPI property table @0x0000000100270000 [ 2.351746] GIC: using cache flushing for LPI property table [ 2.352269] GICv3: CPU0: using allocated LPI pending table @0x0000000100280000 [ 2.353074] random: get_random_bytes called from start_kernel+0x3f0/0x65c with crng_init=0 [ 2.456224] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 2.457545] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 2.458540] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 2.460099] Console: colour dummy device 80x25 [ 2.460534] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000) [ 2.461481] pid_max: default: 32768 minimum: 301 [ 2.461989] LSM: Security Framework initializing [ 2.462474] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 2.463184] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 2.465424] rcu: Hierarchical SRCU implementation. [ 2.466582] Platform MSI: msi-controller@fe640000 domain created [ 2.467147] Platform MSI: msi-controller@fe660000 domain created [ 2.467946] PCI/MSI: /interrupt-controller@fe600000/msi-controller@fe640000 domain created [ 2.468720] PCI/MSI: /interrupt-controller@fe600000/msi-controller@fe660000 domain created [ 2.469575] EFI services will not be available. [ 2.470258] smp: Bringing up secondary CPUs ... I/TC: Secondary CPU 1 initializing I/TC: Secondary CPU 1 switching to normal world boot I/TC: Secondary CPU 2 initializing I/TC: Secondary CPU 2 switching to normal world boot I/TC: Secondary CPU 3 initializing I/TC: Secondary CPU 3 switching to normal world boot I/TC: Secondary CPU 4 initializing I/TC: Secondary CPU 4 switching to normal world boot I/TC: Secondary CPU 5 initializing I/TC: Secondary CPU 5 switching to normal world boot I/TC: Secondary CPU 6 initializing I/TC: Secondary CPU 6 switching to normal world boot I/TC: Secondary CPU 7 initializing I/TC: Secondary CPU 7 switching to normal world boot [ 2.471845] Detected VIPT I-cache on CPU1 [ 2.471871] GICv3: CPU1: found redistributor 100 region 0:0x00000000fe6a0000 [ 2.471885] GICv3: CPU1: using allocated LPI pending table @0x0000000100290000 [ 2.471925] CPU1: Booted secondary processor 0x0000000100 [0x412fd050] [ 2.473131] Detected VIPT I-cache on CPU2 [ 2.473151] GICv3: CPU2: found redistributor 200 region 0:0x00000000fe6c0000 [ 2.473165] GICv3: CPU2: using allocated LPI pending table @0x00000001002a0000 [ 2.473201] CPU2: Booted secondary processor 0x0000000200 [0x412fd050] [ 2.474376] Detected VIPT I-cache on CPU3 [ 2.474393] GICv3: CPU3: found redistributor 300 region 0:0x00000000fe6e0000 [ 2.474405] GICv3: CPU3: using allocated LPI pending table @0x00000001002b0000 [ 2.474438] CPU3: Booted secondary processor 0x0000000300 [0x412fd050] [ 2.475620] CPU features: detected: Spectre-v4 [ 2.475623] CPU features: detected: Spectre-BHB [ 2.475624] Detected PIPT I-cache on CPU4 [ 2.475635] GICv3: CPU4: found redistributor 400 region 0:0x00000000fe700000 [ 2.475642] GICv3: CPU4: using allocated LPI pending table @0x00000001002c0000 [ 2.475664] CPU4: Booted secondary processor 0x0000000400 [0x414fd0b0] [ 2.476800] Detected PIPT I-cache on CPU5 [ 2.476811] GICv3: CPU5: found redistributor 500 region 0:0x00000000fe720000 [ 2.476819] GICv3: CPU5: using allocated LPI pending table @0x00000001002d0000 [ 2.476841] CPU5: Booted secondary processor 0x0000000500 [0x414fd0b0] [ 2.477987] Detected PIPT I-cache on CPU6 [ 2.477998] GICv3: CPU6: found redistributor 600 region 0:0x00000000fe740000 [ 2.478006] GICv3: CPU6: using allocated LPI pending table @0x00000001002e0000 [ 2.478029] CPU6: Booted secondary processor 0x0000000600 [0x414fd0b0] [ 2.479161] Detected PIPT I-cache on CPU7 [ 2.479172] GICv3: CPU7: found redistributor 700 region 0:0x00000000fe760000 [ 2.479179] GICv3: CPU7: using allocated LPI pending table @0x00000001002f0000 [ 2.479202] CPU7: Booted secondary processor 0x0000000700 [0x414fd0b0] [ 2.479257] smp: Brought up 1 node, 8 CPUs [ 2.496384] SMP: Total of 8 processors activated. [ 2.496823] CPU features: detected: Privileged Access Never [ 2.497337] CPU features: detected: User Access Override [ 2.497827] CPU features: detected: 32-bit EL0 Support [ 2.498300] CPU features: detected: Common not Private translations [ 2.498876] CPU features: detected: RAS Extension Support [ 2.499374] CPU features: detected: Data cache clean to the PoU not required for I/D coherence [ 2.500170] CPU features: detected: CRC32 instructions [ 2.500644] CPU features: detected: Speculative Store Bypassing Safe (SSBS) [ 2.501286] CPU features: detected: RCpc load-acquire (LDAPR) [ 2.501888] CPU: All CPU(s) started at EL2 [ 2.504189] devtmpfs: initialized [ 2.512113] Registered cp15_barrier emulation handler [ 2.512581] Registered setend emulation handler [ 2.513063] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns [ 2.513957] futex hash table entries: 2048 (order: 5, 131072 bytes, linear) [ 2.514695] pinctrl core: initialized pinctrl subsystem [ 2.515342] DMI not present or invalid. [ 2.515787] NET: Registered protocol family 16 [ 2.516694] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations [ 2.517410] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 2.518145] audit: initializing netlink subsys (disabled) [ 2.518703] audit: type=2000 audit(0.056:1): state=initialized audit_enabled=0 res=1 [ 2.519076] thermal_sys: Registered thermal governor 'fair_share' [ 2.519423] thermal_sys: Registered thermal governor 'step_wise' [ 2.519982] thermal_sys: Registered thermal governor 'user_space' [ 2.520532] thermal_sys: Registered thermal governor 'power_allocator' [ 2.521187] thermal thermal_zone1: power_allocator: sustainable_power will be estimated [ 2.522534] thermal thermal_zone2: power_allocator: sustainable_power will be estimated [ 2.523290] thermal thermal_zone3: power_allocator: sustainable_power will be estimated [ 2.524101] thermal thermal_zone4: power_allocator: sustainable_power will be estimated [ 2.524852] thermal thermal_zone5: power_allocator: sustainable_power will be estimated [ 2.525603] thermal thermal_zone6: power_allocator: sustainable_power will be estimated [ 2.526350] cpuidle: using governor menu [ 2.526718] Registered FIQ tty driver [ 2.527174] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 2.527890] ASID allocator initialised with 65536 entries [ 2.529284] ramoops: dmesg-0 0x20000@0x0000000000110000 [ 2.529772] ramoops: console 0x80000@0x0000000000130000 [ 2.530265] ramoops: pmsg 0x50000@0x00000000001b0000 [ 2.530942] printk: console [ramoops-1] enabled [ 2.531359] pstore: Registered ramoops as persistent store backend [ 2.531926] ramoops: using 0xf0000@0x110000, ecc: 0 [ 2.562574] rockchip-gpio fd8a0000.gpio: probed /pinctrl/gpio@fd8a0000 [ 2.563344] rockchip-gpio fec20000.gpio: probed /pinctrl/gpio@fec20000 [ 2.564110] rockchip-gpio fec30000.gpio: probed /pinctrl/gpio@fec30000 [ 2.564896] rockchip-gpio fec40000.gpio: probed /pinctrl/gpio@fec40000 [ 2.565639] rockchip-gpio fec50000.gpio: probed /pinctrl/gpio@fec50000 [ 2.566258] rockchip-pinctrl pinctrl: probed pinctrl [ 2.572874] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 2.573491] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 2.574112] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 2.574727] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 2.633681] raid6: neonx8 gen() 5967 MB/s [ 2.690412] raid6: neonx8 xor() 4709 MB/s [ 2.747142] raid6: neonx4 gen() 5886 MB/s [ 2.803871] raid6: neonx4 xor() 4921 MB/s [ 2.860604] raid6: neonx2 gen() 5624 MB/s [ 2.917334] raid6: neonx2 xor() 4441 MB/s [ 2.974064] raid6: neonx1 gen() 4618 MB/s [ 3.030797] raid6: neonx1 xor() 3864 MB/s [ 3.087533] raid6: int64x8 gen() 2791 MB/s [ 3.144259] raid6: int64x8 xor() 1654 MB/s [ 3.200992] raid6: int64x4 gen() 3147 MB/s [ 3.257724] raid6: int64x4 xor() 1649 MB/s [ 3.314460] raid6: int64x2 gen() 2667 MB/s [ 3.371195] raid6: int64x2 xor() 1440 MB/s [ 3.427928] raid6: int64x1 gen() 2187 MB/s [ 3.484663] raid6: int64x1 xor() 1147 MB/s [ 3.485056] raid6: using algorithm neonx8 gen() 5967 MB/s [ 3.485551] raid6: .... xor() 4709 MB/s, rmw enabled [ 3.486006] raid6: using neon recovery algorithm [ 3.486846] fiq_debugger fiq_debugger.0: IRQ fiq not found [ 3.487351] fiq_debugger fiq_debugger.0: IRQ wakeup not found [ 3.487880] fiq_debugger_probe: could not install nmi irq handler [[ 3.488481] printk: console [ttyFIQ0] enabled 3.488481] printk: console [ttyFIQ0] enabled [ 3.489258] printk: bootconsole [uart8250] disabled [ 3.489258] printk: bootconsole [uart8250] disabled [ 3.489773] Registered fiq debugger ttyFIQ0 [ 3.490028] vcc5v0_sys: supplied by vcc12v_dcin [ 3.490113] vcc5v0_usbdcin: supplied by vcc12v_dcin [ 3.490191] vcc5v0_usb: supplied by vcc12v_dcin [ 3.490270] vcc_1v1_nldo_s3: supplied by vcc5v0_sys [ 3.490514] iommu: Default domain type: Passthrough [ 3.490570] rk_iommu fdab9000.iommu: version = 2 [ 3.490833] rk_iommu fdb50800.iommu: version = 2 [ 3.491021] rk_iommu fdb60f00.iommu: version = 2 [ 3.491163] rk_iommu fdb70f00.iommu: version = 2 [ 3.491291] rk_iommu fdb90480.iommu: version = 2 [ 3.491440] rk_iommu fdba0800.iommu: version = 2 [ 3.491595] rk_iommu fdba4800.iommu: version = 2 [ 3.491745] rk_iommu fdba8800.iommu: version = 2 [ 3.491914] rk_iommu fdbac800.iommu: version = 2 [ 3.492062] rk_iommu fdbb0800.iommu: version = 2 [ 3.492209] rk_iommu fdbdf000.iommu: version = 2 [ 3.492415] rk_iommu fdbef000.iommu: version = 2 [ 3.492642] rk_iommu fdc38700.iommu: version = 2 [ 3.492874] rk_iommu fdc48700.iommu: version = 2 [ 3.493036] rk_iommu fdce0800.iommu: version = 2 [ 3.493120] rk_iommu fdd97e00.iommu: version = 2 [ 3.493333] usbcore: registered new interface driver usbfs [ 3.493345] usbcore: registered new interface driver hub [ 3.493357] usbcore: registered new device driver usb [ 3.493384] mc: Linux media interface: v0.10 [ 3.493392] videodev: Linux video capture interface: v2.00 [ 3.493412] pps_core: LinuxPPS API ver. 1 registered [ 3.493415] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 3.493420] PTP clock support registered [ 3.493616] arm-scmi firmware:scmi: SCMI Notifications - Core Enabled. [ 3.493644] arm-scmi firmware:scmi: SCMI Protocol v2.0 'rockchip:' Firmware version 0x0 [ 3.494377] Advanced Linux Sound Architecture Driver Initialized. [ 3.494527] Bluetooth: Core ver 2.22 [ 3.494537] NET: Registered protocol family 31 [ 3.494540] Bluetooth: HCI device and connection manager initialized [ 3.494545] Bluetooth: HCI socket layer initialized [ 3.494549] Bluetooth: L2CAP socket layer initialized [ 3.494554] Bluetooth: SCO socket layer initialized [ 3.495811] rockchip-cpuinfo cpuinfo: SoC : 35881000 [ 3.495816] rockchip-cpuinfo cpuinfo: Serial : 94544b1d1f1920d3 [ 3.496052] clocksource: Switched to clocksource arch_sys_counter [ 3.743883] NET: Registered protocol family 2 [ 3.743979] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 3.745768] tcp_listen_portaddr_hash hash table entries: 4096 (order: 5, 163840 bytes, linear) [ 3.745840] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 3.746162] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear) [ 3.746885] TCP: Hash tables configured (established 65536 bind 65536) [ 3.746930] UDP hash table entries: 4096 (order: 6, 393216 bytes, linear) [ 3.747071] UDP-Lite hash table entries: 4096 (order: 6, 393216 bytes, linear) [ 3.747256] NET: Registered protocol family 1 [ 3.747460] RPC: Registered named UNIX socket transport module. [ 3.747465] RPC: Registered udp transport module. [ 3.747468] RPC: Registered tcp transport module. [ 3.747471] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 3.747760] PCI: CLS 0 bytes, default 64 [ 3.747956] Trying to unpack rootfs image as initramfs... [ 3.944648] Freeing initrd memory: 9016K [ 3.945217] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 3.945546] kvm [1]: IPA Size Limit: 40 bits [ 3.945556] kvm [1]: GICv3: no GICV resource entry [ 3.945560] kvm [1]: disabling GICv2 emulation [ 3.945563] kvm [1]: GIC system register CPU interface enabled [ 3.945670] kvm [1]: vgic interrupt IRQ9 [ 3.945809] kvm [1]: VHE mode initialized successfully [ 3.947576] Initialise system trusted keyrings [ 3.947622] workingset: timestamp_bits=46 max_order=21 bucket_order=0 [ 3.949350] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 3.949562] NFS: Registering the id_resolver key type [ 3.949571] Key type id_resolver registered [ 3.949574] Key type id_legacy registered [ 3.949580] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 3.950023] Key type cifs.spnego registered [ 3.950029] Key type cifs.idmap registered [ 3.950034] ntfs: driver 2.1.32 [Flags: R/O]. [ 3.950077] jffs2: version 2.2. (NAND) 漏 2001-2006 Red Hat, Inc. [ 3.950150] fuse: init (API version 7.32) [ 3.950257] SGI XFS with security attributes, no debug enabled [ 3.969685] NET: Registered protocol family 38 [ 3.969693] xor: measuring software checksum speed [ 3.971030] 8regs : 7381 MB/sec [ 3.972145] 32regs : 8860 MB/sec [ 3.972986] arm64_neon : 11838 MB/sec [ 3.972990] xor: using function: arm64_neon (11838 MB/sec) [ 3.972995] Key type asymmetric registered [ 3.972999] Asymmetric key parser 'x509' registered [ 3.973012] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242) [ 3.973060] io scheduler mq-deadline registered [ 3.973066] io scheduler kyber registered [ 3.973453] rockchip-csi2-dphy-hw fedc0000.csi2-dphy0-hw: csi2 dphy hw probe successfully! [ 3.973632] rockchip-csi2-dphy csi2-dphy0: csi2 dphy0 probe successfully! [ 3.975245] rockchip-usb2phy fd5d8000.syscon:usb2-phy@8000: failed to create phy [ 3.975587] rockchip-usb2phy fd5dc000.syscon:usb2-phy@c000: failed to create phy [ 3.976035] rockchip-usb2phy fd5d4000.syscon:usb2-phy@4000: failed to create phy [ 3.977810] Firefly gpio driver init! [ 3.977881] Firefly gpio driver register return : 0 [ 3.978700] pwm-backlight backlight: supply power not found, using dummy regulator [ 3.978919] iep: Module initialized. [ 3.978945] mpp_service mpp-srv: 42c7305fbcbc author: Chandler Chen 2022-12-15 video: rockchip: mpp: rkvdec: add task timing & timeout for rkvdec [ 3.978950] mpp_service mpp-srv: probe start [ 3.979920] mpp_vdpu2 fdb50400.vdpu: Adding to iommu group 1 [ 3.979939] iommu: Failed to allocate default IOMMU domain of type 4 for group (null) - Falling back to IOMMU_DOMAIN_DMA [ 3.980128] mpp_vdpu2 fdb50400.vdpu: probe device [ 3.980216] mpp_vdpu2 fdb50400.vdpu: reset_group->rw_sem_on=0 [ 3.980221] mpp_vdpu2 fdb50400.vdpu: reset_group->rw_sem_on=0 [ 3.980297] mpp_vdpu2 fdb50400.vdpu: probing finish [ 3.980453] mpp_vepu2 jpege-ccu: probing start [ 3.980457] mpp_vepu2 jpege-ccu: probing finish [ 3.980534] mpp_vepu2 fdba0000.jpege-core: Adding to iommu group 5 [ 3.980544] iommu: Failed to allocate default IOMMU domain of type 4 for group (null) - Falling back to IOMMU_DOMAIN_DMA [ 3.980662] mpp_vepu2 fdba0000.jpege-core: probing start [ 3.980744] mpp_vepu2 fdba0000.jpege-core: attach ccu success [ 3.980813] mpp_vepu2 fdba0000.jpege-core: probing finish [ 3.980899] mpp_vepu2 fdba4000.jpege-core: Adding to iommu group 6 [ 3.980909] iommu: Failed to allocate default IOMMU domain of type 4 for group (null) - Falling back to IOMMU_DOMAIN_DMA [ 3.981027] mpp_vepu2 fdba4000.jpege-core: probing start [ 3.981102] mpp_vepu2 fdba4000.jpege-core: attach ccu success [ 3.981166] mpp_vepu2 fdba4000.jpege-core: probing finish [ 3.981249] mpp_vepu2 fdba8000.jpege-core: Adding to iommu group 7 [ 3.981260] iommu: Failed to allocate default IOMMU domain of type 4 for group (null) - Falling back to IOMMU_DOMAIN_DMA [ 3.981393] mpp_vepu2 fdba8000.jpege-core: probing start [ 3.981467] mpp_vepu2 fdba8000.jpege-core: attach ccu success [ 3.981530] mpp_vepu2 fdba8000.jpege-core: probing finish [ 3.981612] mpp_vepu2 fdbac000.jpege-core: Adding to iommu group 8 [ 3.981622] iommu: Failed to allocate default IOMMU domain of type 4 for group (null) - Falling back to IOMMU_DOMAIN_DMA [ 3.981737] mpp_vepu2 fdbac000.jpege-core: probing start [ 3.981808] mpp_vepu2 fdbac000.jpege-core: attach ccu success [ 3.981874] mpp_vepu2 fdbac000.jpege-core: probing finish [ 3.982079] mpp-iep2 fdbb0000.iep: Adding to iommu group 9 [ 3.982089] iommu: Failed to allocate default IOMMU domain of type 4 for group (null) - Falling back to IOMMU_DOMAIN_DMA [ 3.982202] mpp-iep2 fdbb0000.iep: probe device [ 3.982291] mpp-iep2 fdbb0000.iep: allocate roi buffer failed [ 3.982337] mpp-iep2 fdbb0000.iep: probing finish [ 3.982502] mpp_jpgdec fdb90000.jpegd: Adding to iommu group 4 [ 3.982510] iommu: Failed to allocate default IOMMU domain of type 4 for group (null) - Falling back to IOMMU_DOMAIN_DMA [ 3.982696] mpp_jpgdec fdb90000.jpegd: probe device [ 3.982841] mpp_jpgdec fdb90000.jpegd: probing finish [ 3.983117] mpp_rkvdec2 fdc30000.rkvdec-ccu: rkvdec-ccu, probing start [ 3.983157] mpp_rkvdec2 fdc30000.rkvdec-ccu: probing finish [ 3.983215] mpp_rkvdec2 fdc38100.rkvdec-core: Adding to iommu group 12 [ 3.983224] iommu: Failed to allocate default IOMMU domain of type 4 for group (null) - Falling back to IOMMU_DOMAIN_DMA [ 3.983426] mpp_rkvdec2 fdc38100.rkvdec-core: rkvdec-core, probing start [ 3.983507] mpp_rkvdec2 fdc38100.rkvdec-core: shared_niu_a is not found! [ 3.983511] rkvdec2_init:1010: No niu aclk reset resource define [ 3.983515] mpp_rkvdec2 fdc38100.rkvdec-core: shared_niu_h is not found! [ 3.983518] rkvdec2_init:1013: No niu hclk reset resource define [ 3.983532] mpp_rkvdec2 fdc38100.rkvdec-core: no regulator, devfreq is disabled [ 3.983568] mpp_rkvdec2 fdc38100.rkvdec-core: core_mask=00010001 [ 3.983571] mpp_rkvdec2 fdc38100.rkvdec-core: attach ccu as core 0 [ 3.983711] mpp_rkvdec2 fdc38100.rkvdec-core: sram_start 0x00000000ff001000 [ 3.983715] mpp_rkvdec2 fdc38100.rkvdec-core: rcb_iova 0x00000000fff00000 [ 3.983718] mpp_rkvdec2 fdc38100.rkvdec-core: sram_size 491520 [ 3.983721] mpp_rkvdec2 fdc38100.rkvdec-core: rcb_size 1048576 [ 3.983726] mpp_rkvdec2 fdc38100.rkvdec-core: min_width 512 [ 3.983749] mpp_rkvdec2 fdc38100.rkvdec-core: probing finish [ 3.983811] mpp_rkvdec2 fdc48100.rkvdec-core: Adding to iommu group 13 [ 3.983820] iommu: Failed to allocate default IOMMU domain of type 4 for group (null) - Falling back to IOMMU_DOMAIN_DMA [ 3.984002] mpp_rkvdec2 fdc48100.rkvdec-core: rkvdec-core, probing start [ 3.984085] mpp_rkvdec2 fdc48100.rkvdec-core: shared_niu_a is not found! [ 3.984088] rkvdec2_init:1010: No niu aclk reset resource define [ 3.984092] mpp_rkvdec2 fdc48100.rkvdec-core: shared_niu_h is not found! [ 3.984095] rkvdec2_init:1013: No niu hclk reset resource define [ 3.984107] mpp_rkvdec2 fdc48100.rkvdec-core: no regulator, devfreq is disabled [ 3.984141] mpp_rkvdec2 fdc48100.rkvdec-core: core_mask=00020002 [ 3.984157] mpp_rkvdec2 fdc48100.rkvdec-core: attach ccu as core 1 [ 3.984311] mpp_rkvdec2 fdc48100.rkvdec-core: sram_start 0x00000000ff079000 [ 3.984315] mpp_rkvdec2 fdc48100.rkvdec-core: rcb_iova 0x00000000ffe00000 [ 3.984318] mpp_rkvdec2 fdc48100.rkvdec-core: sram_size 487424 [ 3.984321] mpp_rkvdec2 fdc48100.rkvdec-core: rcb_size 1048576 [ 3.984325] mpp_rkvdec2 fdc48100.rkvdec-core: min_width 512 [ 3.984346] mpp_rkvdec2 fdc48100.rkvdec-core: probing finish [ 3.984476] mpp_rkvenc2 rkvenc-ccu: probing start [ 3.984480] mpp_rkvenc2 rkvenc-ccu: probing finish [ 3.984565] mpp_rkvenc2 fdbd0000.rkvenc-core: Adding to iommu group 10 [ 3.984573] iommu: Failed to allocate default IOMMU domain of type 4 for group (null) - Falling back to IOMMU_DOMAIN_DMA [ 3.984718] mpp_rkvenc2 fdbd0000.rkvenc-core: probing start [ 3.984732] mpp_rkvenc2 fdbd0000.rkvenc-core: link mode task capacity 8 [ 3.984842] mpp_rkvenc2 fdbd0000.rkvenc-core: attach ccu as core 0 [ 3.984913] mpp_rkvenc2 fdbd0000.rkvenc-core: probing finish [ 3.984965] mpp_rkvenc2 fdbe0000.rkvenc-core: Adding to iommu group 11 [ 3.984975] iommu: Failed to allocate default IOMMU domain of type 4 for group (null) - Falling back to IOMMU_DOMAIN_DMA [ 3.985167] mpp_rkvenc2 fdbe0000.rkvenc-core: probing start [ 3.985181] mpp_rkvenc2 fdbe0000.rkvenc-core: link mode task capacity 8 [ 3.985309] mpp_rkvenc2 fdbe0000.rkvenc-core: attach ccu as core 1 [ 3.985373] mpp_rkvenc2 fdbe0000.rkvenc-core: probing finish [ 3.985761] mpp_av1dec: Adding child /av1d@fdc70000 [ 3.985817] mpp_av1dec: register device av1d-master [ 3.985829] mpp_av1dec av1d-master: av1_iommu_of_xlate,784 [ 3.985844] av1_iommu_probe_device,736, consumer : av1d-master, supplier : fdca0000.iommu [ 3.985869] mpp_av1dec av1d-master: Adding to iommu group 16 [ 3.985879] iommu: Failed to allocate default IOMMU domain of type 4 for group (null) - Falling back to IOMMU_DOMAIN_DMA [ 3.986059] mpp_av1dec av1d-master: probing start [ 3.986201] mpp_av1dec av1d-master: probing finish [ 3.986226] mpp_service mpp-srv: probe success [ 3.991119] dma-pl330 fea10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 3.991127] dma-pl330 fea10000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16 [ 3.991763] dma-pl330 fea30000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 3.991769] dma-pl330 fea30000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16 [ 3.992393] dma-pl330 fed10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 3.992398] dma-pl330 fed10000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16 [ 3.992670] rockchip-pvtm fda40000.pvtm: pvtm@0 probed [ 3.992712] rockchip-pvtm fda50000.pvtm: pvtm@1 probed [ 3.992761] rockchip-pvtm fda60000.pvtm: pvtm@2 probed [ 3.992800] rockchip-pvtm fdaf0000.pvtm: pvtm@3 probed [ 3.992835] rockchip-pvtm fdb30000.pvtm: pvtm@4 probed [ 3.993192] rockchip-system-monitor rockchip-system-monitor: system monitor probe [ 3.994039] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled [ 3.994309] fd890000.serial: ttyS0 at MMIO 0xfd890000 (irq = 28, base_baud = 1500000) is a 16550A [ 3.994560] feb40000.serial: ttyS1 at MMIO 0xfeb40000 (irq = 90, base_baud = 1500000) is a 16550A [ 3.994721] feb80000.serial: ttyS5 at MMIO 0xfeb80000 (irq = 91, base_baud = 1500000) is a 16550A [ 3.994934] feb90000.serial: ttyS6 at MMIO 0xfeb90000 (irq = 92, base_baud = 1500000) is a 16550A [ 3.995735] random: fast init done [ 3.995787] random: crng init done [ 3.996346] rockchip-vop2 fdd90000.vop: Adding to iommu group 15 [ 3.996360] iommu: Failed to allocate default IOMMU domain of type 4 for group (null) - Falling back to IOMMU_DOMAIN_DMA [ 4.003023] panel-simple-dsi fde20000.dsi.0: supply power not found, using dummy regulator [ 4.005128] brd: module loaded [ 4.007574] loop: module loaded [ 4.007737] zram: Added device: zram0 [ 4.007843] lkdtm: No crash points registered, enable through debugfs [ 4.008123] system_heap: orders[0] = 6 [ 4.008127] system_heap: orders[1] = 4 [ 4.008130] system_heap: orders[2] = 0 [ 4.009128] rockchip-spi feb10000.spi: no high_speed pinctrl state [ 4.009576] rockchip-spi feb20000.spi: no high_speed pinctrl state [ 4.010506] rk806 spi2.0: chip id: RK806,ver:0x2, 0x1 [ 4.010643] rk806 spi2.0: ON: 0x40 OFF:0x0 [ 4.012138] vdd_gpu_s0: supplied by vcc5v0_sys [ 4.013078] vdd_cpu_lit_s0: supplied by vcc5v0_sys [ 4.013625] vdd_log_s0: supplied by vcc5v0_sys [ 4.014159] vdd_vdenc_s0: supplied by vcc5v0_sys [ 4.014750] vdd_ddr_s0: supplied by vcc5v0_sys [ 4.015104] vdd2_ddr_s3: supplied by vcc5v0_sys [ 4.015615] vdd_2v0_pldo_s3: supplied by vcc5v0_sys [ 4.016099] vcc_3v3_s3: supplied by vcc5v0_sys [ 4.016546] vddq_ddr_s0: supplied by vcc5v0_sys [ 4.017061] vcc_1v8_s3: supplied by vcc5v0_sys [ 4.017573] vdd_0v75_s3: supplied by vcc_1v1_nldo_s3 [ 4.018127] vdd_ddr_pll_s0: supplied by vcc_1v1_nldo_s3 [ 4.018611] avdd_0v75_s0: supplied by vcc_1v1_nldo_s3 [ 4.019068] vdd_0v85_s0: supplied by vcc_1v1_nldo_s3 [ 4.019535] vdd_0v75_s0: supplied by vcc_1v1_nldo_s3 [ 4.020095] avcc_1v8_s0: supplied by vdd_2v0_pldo_s3 [ 4.020702] vcc_1v8_s0: supplied by vdd_2v0_pldo_s3 [ 4.021221] avdd_1v2_s0: supplied by vdd_2v0_pldo_s3 [ 4.021735] vcc_3v3_s0: supplied by vcc5v0_sys [ 4.022192] vccio_sd_s0: supplied by vcc5v0_sys [ 4.022689] pldo6_s3: supplied by vcc5v0_sys [ 4.023113] rk806 spi2.0: no sleep-setting state [ 4.023119] rk806 spi2.0: no reset-setting pinctrl state [ 4.023122] rk806 spi2.0: no dvs-setting pinctrl state [ 4.024920] wk2xxx_init: SPI driver for spi to Uart chip WK2XXX, etc. [ 4.024925] wk2xxx_init: V2.4 On 2022.07.24 [ 4.024941] register firefly_spi_init spi return v = :0 [ 4.025194] wireguard: allowedips self-tests: pass [ 4.029358] wireguard: nonce counter self-tests: pass [ 4.291194] wireguard: ratelimiter self-tests: pass [ 4.291279] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 4.291284] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld . All Rights Reserved. [ 4.291628] tun: Universal TUN/TAP device driver, 1.6 [ 4.291734] CAN device driver interface [ 4.293142] rk_gmac-dwmac fe1b0000.ethernet: IRQ eth_lpi not found [ 4.293265] rk_gmac-dwmac fe1b0000.ethernet: no regulator found [ 4.293271] rk_gmac-dwmac fe1b0000.ethernet: clock input or output? (output). [ 4.293277] rk_gmac-dwmac fe1b0000.ethernet: TX delay(0x47). [ 4.293282] rk_gmac-dwmac fe1b0000.ethernet: Can not read property: rx_delay. [ 4.293286] rk_gmac-dwmac fe1b0000.ethernet: set rx_delay to 0xffffffff [ 4.293300] rk_gmac-dwmac fe1b0000.ethernet: integrated PHY? (no). [ 4.293305] rk_gmac-dwmac fe1b0000.ethernet: cannot get clock mac_clk_rx [ 4.293310] rk_gmac-dwmac fe1b0000.ethernet: cannot get clock mac_clk_tx [ 4.293320] rk_gmac-dwmac fe1b0000.ethernet: cannot get clock clk_mac_speed [ 4.293536] rk_gmac-dwmac fe1b0000.ethernet: init for RGMII_RXID [ 4.293647] rk_gmac-dwmac fe1b0000.ethernet: User ID: 0x30, Synopsys ID: 0x51 [ 4.293653] rk_gmac-dwmac fe1b0000.ethernet: DWMAC4/5 [ 4.293658] rk_gmac-dwmac fe1b0000.ethernet: DMA HW capability register supported [ 4.293662] rk_gmac-dwmac fe1b0000.ethernet: RX Checksum Offload Engine supported [ 4.293666] rk_gmac-dwmac fe1b0000.ethernet: TX Checksum insertion supported [ 4.293669] rk_gmac-dwmac fe1b0000.ethernet: Wake-Up On Lan supported [ 4.293697] rk_gmac-dwmac fe1b0000.ethernet: TSO supported [ 4.293702] rk_gmac-dwmac fe1b0000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 4.293706] rk_gmac-dwmac fe1b0000.ethernet: Enabled Flow TC (entries=2) [ 4.293710] rk_gmac-dwmac fe1b0000.ethernet: TSO feature enabled [ 4.293715] rk_gmac-dwmac fe1b0000.ethernet: Using 32 bits DMA width [ 4.429506] RTL8211F Gigabit Ethernet stmmac-0:01: [phy_probe-2991] led_status_value normal [ 4.430043] rk_gmac-dwmac fe1c0000.ethernet: IRQ eth_lpi not found [ 4.430143] rk_gmac-dwmac fe1c0000.ethernet: no regulator found [ 4.430149] rk_gmac-dwmac fe1c0000.ethernet: clock input or output? (output). [ 4.430153] rk_gmac-dwmac fe1c0000.ethernet: TX delay(0x4f). [ 4.430158] rk_gmac-dwmac fe1c0000.ethernet: Can not read property: rx_delay. [ 4.430162] rk_gmac-dwmac fe1c0000.ethernet: set rx_delay to 0xffffffff [ 4.430169] rk_gmac-dwmac fe1c0000.ethernet: integrated PHY? (no). [ 4.430174] rk_gmac-dwmac fe1c0000.ethernet: cannot get clock mac_clk_rx [ 4.430179] rk_gmac-dwmac fe1c0000.ethernet: cannot get clock mac_clk_tx [ 4.430189] rk_gmac-dwmac fe1c0000.ethernet: cannot get clock clk_mac_speed [ 4.430403] rk_gmac-dwmac fe1c0000.ethernet: init for RGMII_RXID [ 4.430495] rk_gmac-dwmac fe1c0000.ethernet: User ID: 0x30, Synopsys ID: 0x51 [ 4.430500] rk_gmac-dwmac fe1c0000.ethernet: DWMAC4/5 [ 4.430505] rk_gmac-dwmac fe1c0000.ethernet: DMA HW capability register supported [ 4.430509] rk_gmac-dwmac fe1c0000.ethernet: RX Checksum Offload Engine supported [ 4.430512] rk_gmac-dwmac fe1c0000.ethernet: TX Checksum insertion supported [ 4.430516] rk_gmac-dwmac fe1c0000.ethernet: Wake-Up On Lan supported [ 4.430542] rk_gmac-dwmac fe1c0000.ethernet: TSO supported [ 4.430546] rk_gmac-dwmac fe1c0000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 4.430550] rk_gmac-dwmac fe1c0000.ethernet: Enabled Flow TC (entries=2) [ 4.430554] rk_gmac-dwmac fe1c0000.ethernet: TSO feature enabled [ 4.430558] rk_gmac-dwmac fe1c0000.ethernet: Using 32 bits DMA width [ 4.565332] phy_rtl8211f_led_fixup in [ 4.585977] hcq : phy_rtl8211e_eee_fixup in [ 4.607187] RTL8211F Gigabit Ethernet stmmac-1:01: [phy_probe-2991] led_status_value normal [ 4.607919] usbcore: registered new interface driver asix [ 4.607945] usbcore: registered new interface driver ax88179_178a [ 4.607956] usbcore: registered new interface driver cdc_ether [ 4.607967] usbcore: registered new interface driver net1080 [ 4.607980] usbcore: registered new interface driver cdc_subset [ 4.607991] usbcore: registered new interface driver zaurus [ 4.608006] usbcore: registered new interface driver cdc_ncm [ 4.608020] usbcore: registered new interface driver qmi_wwan_q [ 4.608032] usbcore: registered new interface driver qmi_wwan [ 4.610102] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.610110] ehci-pci: EHCI PCI platform driver [ 4.610132] ehci-platform: EHCI generic platform driver [ 4.610293] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 4.610299] ohci-platform: OHCI generic platform driver [ 4.610603] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller [ 4.610669] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 1 [ 4.610742] xhci-hcd xhci-hcd.3.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000080002010010 [ 4.610769] xhci-hcd xhci-hcd.3.auto: irq 119, io mem 0xfcd00000 [ 4.610890] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 4.610895] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.610899] usb usb1: Product: xHCI Host Controller [ 4.610903] usb usb1: Manufacturer: Linux 5.10.110 xhci-hcd [ 4.610907] usb usb1: SerialNumber: xhci-hcd.3.auto [ 4.611076] hub 1-0:1.0: USB hub found [ 4.611089] hub 1-0:1.0: 1 port detected [ 4.611199] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller [ 4.611251] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 2 [ 4.611258] xhci-hcd xhci-hcd.3.auto: Host supports USB 3.0 SuperSpeed [ 4.611282] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.611320] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10 [ 4.611325] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.611329] usb usb2: Product: xHCI Host Controller [ 4.611333] usb usb2: Manufacturer: Linux 5.10.110 xhci-hcd [ 4.611337] usb usb2: SerialNumber: xhci-hcd.3.auto [ 4.611475] hub 2-0:1.0: USB hub found [ 4.611486] hub 2-0:1.0: 1 port detected [ 4.611616] usbcore: registered new interface driver cdc_acm [ 4.611621] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 4.611633] usbcore: registered new interface driver cdc_wdm [ 4.611660] usbcore: registered new interface driver usbserial_generic [ 4.611670] usbserial: USB Serial support registered for generic [ 4.611682] usbcore: registered new interface driver ch341 [ 4.611690] usbserial: USB Serial support registered for ch341-uart [ 4.611704] usbcore: registered new interface driver cp210x [ 4.611711] usbserial: USB Serial support registered for cp210x [ 4.611727] usbcore: registered new interface driver ftdi_sio [ 4.611735] usbserial: USB Serial support registered for FTDI USB Serial Device [ 4.611761] usbcore: registered new interface driver keyspan [ 4.611769] usbserial: USB Serial support registered for Keyspan - (without firmware) [ 4.611777] usbserial: USB Serial support registered for Keyspan 1 port adapter [ 4.611784] usbserial: USB Serial support registered for Keyspan 2 port adapter [ 4.611792] usbserial: USB Serial support registered for Keyspan 4 port adapter [ 4.611805] usbcore: registered new interface driver option [ 4.611813] usbserial: USB Serial support registered for GSM modem (1-port) [ 4.611845] usbcore: registered new interface driver oti6858 [ 4.611853] usbserial: USB Serial support registered for oti6858 [ 4.611867] usbcore: registered new interface driver pl2303 [ 4.611875] usbserial: USB Serial support registered for pl2303 [ 4.611888] usbcore: registered new interface driver qcserial [ 4.611896] usbserial: USB Serial support registered for Qualcomm USB modem [ 4.611910] usbcore: registered new interface driver sierra [ 4.611917] usbserial: USB Serial support registered for Sierra USB modem [ 4.612281] [HXTP] himax_hx83102_init [ 4.612286] [HXTP] himax_hx83102_probe:Enter [ 4.612289] [HXTP] Himax common touch panel driver init [ 4.612328] usbcore: registered new interface driver usbtouchscreen [ 4.613319] input: rk805 pwrkey as /devices/platform/feb20000.spi/spi_master/spi2/spi2.0/rk805-pwrkey.1.auto/input/input0 [ 4.613511] i2c /dev entries driver [ 4.616876] vdd_cpu_big0_s0: supplied by vcc5v0_sys [ 4.625340] vdd_cpu_big1_s0: supplied by vcc5v0_sys [ 4.634193] vdd_npu_s0: supplied by vcc5v0_sys [ 4.639895] [HXTP] himax_chip_common_probe:Enter [ 4.639900] [HXTP] Prepare kernel fp [ 4.645609] [HXTP] PDATA START [ 4.645616] [HXTP] ic_data START [ 4.645622] [HXTP] DT-himax_parse_dt:panel-coords = 0, 799, 0, 1279 [ 4.645628] [HXTP] DT-himax_parse_dt:display-coords = (800, 1280) [ 4.645642] [HXTP] DT:gpio_3v3_en value is not valid [ 4.645646] [HXTP] DT:gpio_irq=112, gpio_rst=113, gpio_3v3_en=-2 [ 4.645650] [HXTP] DT:protocol_type=1 [ 4.645654] [HXTP] DT-No vk info in DT [ 4.647691] [HXTP] himax_get_ksym_idx: symtable size: 1 [ 4.647696] [HXTP] hx83102_pin_reset: Now reset the Touch chip. [ 4.729807] [HXTP][ERROR] himax_bus_read: i2c_read_block retry over 3 [ 4.729812] [HXTP][ERROR] hx83102_chip_detect: i2c access fail! [ 4.729817] [HXTP] himax_chip_common_init:num=0,chip NOT found! go Next [ 4.729820] [HXTP][ERROR] himax_chip_common_init: chip detect failed! [ 4.729835] himax_tp: probe of 1-0048 failed with error -9 [ 4.730814] pca953x 6-0021: supply vcc not found, using dummy regulator [ 4.730859] pca953x 6-0021: using no AI [ 4.731672] rtc-hym8563 6-0051: could not init device, -6 [ 4.732032] pca953x 6-0020: supply vcc not found, using dummy regulator [ 4.732073] pca953x 6-0020: using no AI [ 4.732131] pca953x 6-0020: failed writing register [ 4.732795] rkcifhw fdce0000.rkcif: Adding to iommu group 14 [ 4.732810] iommu: Failed to allocate default IOMMU domain of type 4 for group (null) - Falling back to IOMMU_DOMAIN_DMA [ 4.733074] rkcifhw fdce0000.rkcif: No reserved memory region assign to CIF [ 4.733139] rkcif rkcif-mipi-lvds2: Adding to iommu group 14 [ 4.733153] rkcif rkcif-mipi-lvds2: rkcif driver version: v00.01.0a [ 4.733201] rkcif rkcif-mipi-lvds2: attach to cif hw node [ 4.733205] rkcif rkcif-mipi-lvds2: rkcif wait line 0 [ 4.733211] : terminal subdev does not exist [ 4.733215] : terminal subdev does not exist [ 4.733218] : terminal subdev does not exist [ 4.733222] : terminal subdev does not exist [ 4.733226] : get_remote_sensor: video pad[0] is null [ 4.733231] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed! [ 4.733235] : get_remote_sensor: video pad[0] is null [ 4.733238] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed! [ 4.733242] : get_remote_sensor: video pad[0] is null [ 4.733245] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed! [ 4.733249] : get_remote_sensor: video pad[0] is null [ 4.733252] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed! [ 4.733815] rkcif rkcif-mipi-lvds2: No memory-region-thunderboot specified [ 4.734413] rkcif rkcif-mipi-lvds2: Entity type for entity rockchip-mipi-csi2 was not initialized! [ 4.734420] rockchip-mipi-csi2: Async registered subdev [ 4.734427] rockchip-mipi-csi2: probe success, v4l2_dev:rkcif-mipi-lvds2! [ 4.735668] rk_hdmirx fdee0000.hdmirx-controller: No reserved memory for HDMIRX, use default CMA [ 4.735688] rk_hdmirx fdee0000.hdmirx-controller: hdmirx_probe: cpu_aff:0x400, Bound_cpu:4, wdt_cfg_bound_cpu:5 [ 4.736177] rk_hdmirx fdee0000.hdmirx-controller: hdmirx_audio_interrupts_setup: 0 [ 4.736778] rk_hdmirx fdee0000.hdmirx-controller: rk_hdmirx_hdcp_register success [ 4.736795] rk_hdmirx fdee0000.hdmirx-controller: fdee0000.hdmirx-controller driver probe ok! [ 4.736862] usbcore: registered new interface driver uvcvideo [ 4.736866] USB Video Class driver (1.1.1) [ 4.738421] rockchip-thermal fec00000.tsadc: Missing rockchip,grf property [ 4.738848] rockchip-thermal fec00000.tsadc: tsadc is probed successfully! [ 4.739279] device-mapper: ioctl: 4.44.0-ioctl (2021-02-01) initialised: dm-devel@redhat.com [ 4.739431] Bluetooth: HCI UART driver ver 2.3 [ 4.739436] Bluetooth: HCI UART protocol H4 registered [ 4.739439] Bluetooth: HCI UART protocol ATH3K registered [ 4.739461] usbcore: registered new interface driver bfusb [ 4.740127] cpu cpu0: bin=2 [ 4.740299] cpu cpu0: leakage=15 [ 4.741705] cpu cpu0: pvtm=1510 [ 4.741766] cpu cpu0: pvtm-volt-sel=5 [ 4.743641] cpu cpu4: bin=2 [ 4.743810] cpu cpu4: leakage=11 [ 4.750256] cpu cpu4: pvtm=1739 [ 4.754161] cpu cpu4: pvtm-volt-sel=5 [ 4.756778] cpu cpu6: bin=2 [ 4.756946] cpu cpu6: leakage=12 [ 4.763402] cpu cpu6: pvtm=1751 [ 4.767331] cpu cpu6: pvtm-volt-sel=6 [ 4.768682] cpu cpu0: avs=0 [ 4.769036] cpu cpu4: avs=0 [ 4.769375] cpu cpu6: avs=0 [ 4.769555] cpu cpu0: EM: created perf domain [ 4.769585] cpu cpu0: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=1608000000 h_table=0 [ 4.770111] cpu cpu4: EM: created perf domain [ 4.770134] cpu cpu4: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=2208000000 h_table=0 [ 4.778358] cpu cpu6: EM: created perf domain [ 4.779051] cpu cpu6: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=2208000000 h_table=0 [ 4.793322] sdhci: Secure Digital Host Controller Interface driver [ 4.793356] sdhci: Copyright(c) Pierre Ossman [ 4.793363] Synopsys Designware Multimedia Card Interface Driver [ 4.793669] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.796799] arm-scmi firmware:scmi: Failed. SCMI protocol 17 not active. [ 4.796903] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 4.798111] cryptodev: driver 1.12 loaded. [ 4.798196] hid: raw HID events driver (C) Jiri Kosina [ 4.798506] usbcore: registered new interface driver usbhid [ 4.798518] usbhid: USB HID core driver [ 4.798854] ashmem: initialized [ 4.802724] Firefly adc init [ 4.802741] Firefly adc-->FIREFLY_ADC_SAMPLE_JIFFIES: 16 [ 4.802747] Firefly adc-->MSEC_PER_SEC: 1000 [ 4.802752] Firefly adc-->HZ: 300 [ 4.802956] Firefly adc-->ret: 0 [ 4.803180] optee: probing for conduit method. [ 4.803201] optee: revision 3.13 (4542e1ef) [ 4.803855] optee: initialized driver [ 4.804716] usbcore: registered new interface driver snd-usb-audio [ 4.828092] mmc0: SDHCI controller on fe2e0000.mmc [fe2e0000.mmc] using ADMA [ 4.846876] ES8323 3-0011: i2c recv Failed [ 4.855948] Initializing XFRM netlink socket [ 4.856292] NET: Registered protocol family 10 [ 4.857196] Segment Routing with IPv6 [ 4.857453] NET: Registered protocol family 17 [ 4.857475] NET: Registered protocol family 15 [ 4.857522] Bridge firewalling registered [ 4.857530] can: controller area network core [ 4.857572] NET: Registered protocol family 29 [ 4.857580] can: raw protocol [ 4.857589] can: broadcast manager protocol [ 4.857600] can: netlink gateway - max_hops=1 [ 4.857938] Bluetooth: RFCOMM TTY layer initialized [ 4.857953] Bluetooth: RFCOMM socket layer initialized [ 4.857971] Bluetooth: RFCOMM ver 1.11 [ 4.857983] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 4.857990] Bluetooth: BNEP filters: protocol multicast [ 4.858001] Bluetooth: BNEP socket layer initialized [ 4.858008] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 4.858017] Bluetooth: HIDP socket layer initialized [ 4.858050] 8021q: 802.1Q VLAN Support v1.8 [ 4.858069] [BT_RFKILL]: Enter rfkill_rk_init [ 4.858075] [WLAN_RFKILL]: Enter rfkill_wlan_init [ 4.858411] [WLAN_RFKILL]: Enter rfkill_wlan_probe [ 4.858440] [WLAN_RFKILL]: can't find rockchip,grf property [ 4.858448] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6275p [ 4.858455] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control. [ 4.858462] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio. [ 4.858483] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,poweren_gpio = 20 flags = 0. [ 4.858507] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,host_wake_irq = 10, flags = 0. [ 4.858516] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found ! [ 4.858523] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio [ 4.858530] [WLAN_RFKILL]: rfkill_set_wifi_bt_power: 1 [ 4.858538] [WLAN_RFKILL]: Exit rfkill_wlan_probe [ 4.858838] Key type dns_resolver registered [ 4.859996] xc7160 3-001b: T-chip firefly camera driver version: 00.01.04 [ 4.860133] xc7160 3-001b: supply avdd not found, using dummy regulator [ 4.860251] xc7160 3-001b: supply dovdd not found, using dummy regulator [ 4.860300] xc7160 3-001b: supply dvdd not found, using dummy regulator [ 4.860360] xc7160 3-001b: could not get default pinstate [ 4.860368] xc7160 3-001b: could not get sleep pinstate [ 4.860386] xc7160 3-001b: Success to get xc7160 endpoint data lanes, dts uses 4 lanes [ 4.861142] mmc0: Host Software Queue enabled [ 4.861158] mmc0: new HS400 Enhanced strobe MMC card at address 0001 [ 4.861677] mmcblk0: mmc0:0001 IX2964 58.3 GiB [ 4.861869] mmcblk0boot0: mmc0:0001 IX2964 partition 1 4.00 MiB [ 4.862050] mmcblk0boot1: mmc0:0001 IX2964 partition 2 4.00 MiB [ 4.862213] mmcblk0rpmb: mmc0:0001 IX2964 partition 3 4.00 MiB, chardev (234:0) [ 4.864638] mmcblk0: p1 p2 p3 p4 p5 p6 p7 [ 4.915847] xc7160 3-001b: write XC7160_REG_HIGH_SELECT failed [ 4.916295] xc7160: probe of 3-001b failed with error -5 [ 4.916996] registered taskstats version 1 [ 4.917014] Loading compiled-in X.509 certificates [ 4.919047] Btrfs loaded, crc32c=crc32c-generic [ 4.919254] pstore: Using crash dump compression: deflate [ 4.920224] rga3_core0 fdb60000.rga: Adding to iommu group 2 [ 4.920292] iommu: Failed to allocate default IOMMU domain of type 4 for group (null) - Falling back to IOMMU_DOMAIN_DMA [ 4.920566] rga: rga3_core0, irq = 34, match scheduler [ 4.921127] rga: rga3_core0 hardware loaded successfully, hw_version:3.0.76831. [ 4.921210] rga: rga3_core0 probe successfully [ 4.921765] rga3_core1 fdb70000.rga: Adding to iommu group 3 [ 4.921795] iommu: Failed to allocate default IOMMU domain of type 4 for group (null) - Falling back to IOMMU_DOMAIN_DMA [ 4.922041] rga: rga3_core1, irq = 35, match scheduler [ 4.922509] rga: rga3_core1 hardware loaded successfully, hw_version:3.0.76831. [ 4.922596] rga: rga3_core1 probe successfully [ 4.923184] rga: rga2, irq = 36, match scheduler [ 4.923786] rga: rga2 hardware loaded successfully, hw_version:3.2.63318. [ 4.923807] rga: rga2 probe successfully [ 4.924159] rga_iommu: IOMMU binding successfully, default mapping core[0x1] [ 4.924485] rga: Module initialized. v1.2.23 [ 4.924499] [ 4.924507] ******************************************************************** [ 4.924516] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** [ 4.924524] ** ** [ 4.924532] ** WRITEABLE clk DebugFS SUPPORT HAS BEEN ENABLED IN THIS KERNEL ** [ 4.924540] ** ** [ 4.924549] ** This means that this kernel is built to expose clk operations ** [ 4.924556] ** such as parent or rate setting, enabling, disabling, etc. ** [ 4.924564] ** to userspace, which may compromise security on your system. ** [ 4.924572] ** ** [ 4.924579] ** If you see this message and you are not debugging the ** [ 4.924587] ** kernel, report this immediately to your vendor! ** [ 4.924594] ** ** [ 4.924602] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** [ 4.924610] ******************************************************************** [ 4.966860] pcie30_avdd1v8: supplied by avcc_1v8_s0 [ 4.966944] mali fb000000.gpu: Kernel DDK version g15p0-01eac0 [ 4.967433] pcie30_avdd0v75: supplied by avdd_0v75_s0 [ 4.967536] mali fb000000.gpu: bin=2 [ 4.967717] mali fb000000.gpu: leakage=20 [ 4.967760] debugfs: Directory 'fb000000.gpu-mali' with parent 'vdd_gpu_s0' already present! [ 4.969276] mali fb000000.gpu: pvtm=887 [ 4.969325] mali fb000000.gpu: pvtm-volt-sel=4 [ 4.969653] rockchip-dmc dmc: leakage=42 [ 4.969671] rockchip-dmc dmc: leakage-volt-sel=1 [ 4.970168] mali fb000000.gpu: avs=0 [ 4.970267] W : [File] : drivers/gpu/arm/bifrost/platform/rk/mali_kbase_config_rk.c; [Line] : 136; [Func] : kbase_platform_rk_init(); power-off-delay-ms not available. [ 4.970278] rockchip-dmc dmc: avs=0 [ 4.970297] rockchip-dmc dmc: current ATF version 0x100 [ 4.970428] rockchip-dmc dmc: normal_rate = 1560000000 [ 4.970438] rockchip-dmc dmc: reboot_rate = 2112000000 [ 4.970447] rockchip-dmc dmc: suspend_rate = 528000000 [ 4.970456] rockchip-dmc dmc: video_4k_rate = 1560000000 [ 4.970464] rockchip-dmc dmc: video_4k_10b_rate = 1560000000 [ 4.970472] rockchip-dmc dmc: video_svep_rate = 1560000000 [ 4.970481] rockchip-dmc dmc: boost_rate = 2112000000 [ 4.970489] rockchip-dmc dmc: fixed_rate(isp|cif0|cif1|dualview) = 2112000000 [ 4.970497] rockchip-dmc dmc: performance_rate = 2112000000 [ 4.970506] rockchip-dmc dmc: hdmirx_rate = 2112000000 [ 4.970518] rockchip-dmc dmc: failed to get vop bandwidth to dmc rate [ 4.970526] rockchip-dmc dmc: failed to get vop pn to msch rl [ 4.970660] rockchip-dmc dmc: l=10000 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0 [ 4.970710] rockchip-dmc dmc: could not find power_model node [ 4.970728] mali fb000000.gpu: GPU hardware issue table may need updating: [ 4.970728] r0p0 status 5 is unknown; treating as r0p0 status 0 [ 4.970743] mali fb000000.gpu: GPU identified as 0x7 arch 10.8.6 r0p0 status 0 [ 4.970829] mali fb000000.gpu: No priority control manager is configured [ 4.971001] mali fb000000.gpu: No memory group manager is configured [ 4.971033] mali fb000000.gpu: Protected memory allocator not available [ 4.971429] mali fb000000.gpu: Capping CSF_FIRMWARE_TIMEOUT to CSF_FIRMWARE_PING_TIMEOUT [ 4.972057] mali fb000000.gpu: Couldn't find power_model DT node matching 'arm,mali-simple-power-model' [ 4.972071] mali fb000000.gpu: Error -22, no DT entry: mali-simple-power-model.static-coefficient = 1*[0] [ 4.972267] mali fb000000.gpu: Error -22, no DT entry: mali-simple-power-model.dynamic-coefficient = 1*[0] [ 4.972444] mali fb000000.gpu: Error -22, no DT entry: mali-simple-power-model.ts = 4*[0] [ 4.972617] mali fb000000.gpu: Error -22, no DT entry: mali-simple-power-model.thermal-zone = '' [ 4.975092] mali fb000000.gpu: Using configured power model mali-lodx-power-model, and fallback mali-simple-power-model [ 4.975228] mali fb000000.gpu: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=800000000 h_table=0 [ 4.976137] mali fb000000.gpu: Probed as mali0 [ 4.988062] rockchip-usb2phy fd5d8000.syscon:usb2-phy@8000: failed to create phy [ 4.988398] vendor storage:20190527 ret = 0 [ 4.988799] rockchip-usb2phy fd5dc000.syscon:usb2-phy@c000: failed to create phy [ 4.989503] rockchip-usb2phy fd5d4000.syscon:usb2-phy@4000: failed to create phy [ 4.999169] input: adc-keys as /devices/platform/adc-keys/input/input1 [ 5.002984] debugfs: File 'Capture' in directory 'dapm' already present! [ 5.004200] input: rockchip-dp0 rockchip-dp0 as /devices/platform/dp0-sound/sound/card1/input2 [ 5.006684] rockchip-usb2phy fd5d8000.syscon:usb2-phy@8000: failed to create phy [ 5.007474] rockchip-usb2phy fd5dc000.syscon:usb2-phy@c000: failed to create phy [ 5.008228] rockchip-usb2phy fd5d4000.syscon:usb2-phy@4000: failed to create phy [ 5.011361] rockchip-usb2phy fd5d8000.syscon:usb2-phy@8000: failed to create phy [ 5.012113] rockchip-usb2phy fd5dc000.syscon:usb2-phy@c000: failed to create phy [ 5.012887] rockchip-usb2phy fd5d4000.syscon:usb2-phy@4000: failed to create phy [ 5.016208] rkcif rkcif-mipi-lvds2: clear unready subdev num: 1 [ 5.016260] rockchip-csi2-dphy0: No link between dphy and sensor [ 5.016984] rockchip-csi2-dphy0: No link between dphy and sensor [ 5.017023] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed! [ 5.017075] rkcif-mipi-lvds2: Async subdev notifier completed [ 5.017087] rockchip-csi2-dphy0: No link between dphy and sensor [ 5.017145] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed! [ 5.017160] rkcif-mipi-lvds2: There is not terminal subdev, not synchronized with ISP [ 5.017177] rockchip-csi2-dphy0: No link between dphy and sensor [ 5.017218] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed! [ 5.017229] rkcif-mipi-lvds2: There is not terminal subdev, not synchronized with ISP [ 5.017823] pc9202: sw2001_read(0x1) return 0x1 [ 5.017838] status=0x1 [ 5.017849] ====== i2c detect success watchdog init ====== [ 5.020071] dwmmc_rockchip fe2c0000.mmc: IDMAC supports 32-bit address mode. [ 5.020101] dwmmc_rockchip fe2c0000.mmc: Using internal DMA controller. [ 5.020117] dwmmc_rockchip fe2c0000.mmc: Version ID is 270a [ 5.020172] dwmmc_rockchip fe2c0000.mmc: DW MMC controller at irq 76,32 bit host data width,256 deep fifo [ 5.020579] rockchip-usb2phy fd5d8000.syscon:usb2-phy@8000: failed to create phy [ 5.020799] RKNPU fdab0000.npu: Adding to iommu group 0 [ 5.020860] iommu: Failed to allocate default IOMMU domain of type 4 for group (null) - Falling back to IOMMU_DOMAIN_DMA [ 5.021063] RKNPU fdab0000.npu: RKNPU: rknpu iommu is enabled, using iommu mode [ 5.021250] rockchip-usb2phy fd5dc000.syscon:usb2-phy@c000: failed to create phy [ 5.021839] rockchip-usb2phy fd5d4000.syscon:usb2-phy@4000: failed to create phy [ 5.022529] RKNPU fdab0000.npu: can't request region for resource [mem 0xfdab0000-0xfdabffff] [ 5.022560] RKNPU fdab0000.npu: can't request region for resource [mem 0xfdac0000-0xfdacffff] [ 5.022582] RKNPU fdab0000.npu: can't request region for resource [mem 0xfdad0000-0xfdadffff] [ 5.023189] [drm] Initialized rknpu 0.8.2 20220829 for fdab0000.npu on minor 0 [ 5.027334] RKNPU fdab0000.npu: bin=2 [ 5.027528] RKNPU fdab0000.npu: leakage=11 [ 5.027594] debugfs: Directory 'fdab0000.npu-rknpu' with parent 'vdd_npu_s0' already present! [ 5.034197] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) [ 5.035370] RKNPU fdab0000.npu: pvtm=886 [ 5.040124] RKNPU fdab0000.npu: pvtm-volt-sel=4 [ 5.040954] RKNPU fdab0000.npu: avs=0 [ 5.041147] RKNPU fdab0000.npu: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=800000000 h_table=0 [ 5.048279] rockchip-usb2phy fd5d8000.syscon:usb2-phy@8000: failed to create phy [ 5.051623] rockchip-usb2phy fd5dc000.syscon:usb2-phy@c000: failed to create phy [ 5.052416] RKNPU fdab0000.npu: failed to find power_model node [ 5.052437] RKNPU fdab0000.npu: RKNPU: failed to initialize power model [ 5.052451] RKNPU fdab0000.npu: RKNPU: failed to get dynamic-coefficient [ 5.052605] rockchip-usb2phy fd5d4000.syscon:usb2-phy@4000: failed to create phy [ 5.053348] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 5.053794] rockchip-usb2phy fd5d8000.syscon:usb2-phy@8000: failed to create phy [ 5.054025] rockchip-usb2phy fd5dc000.syscon:usb2-phy@c000: failed to create phy [ 5.054246] rockchip-usb2phy fd5d4000.syscon:usb2-phy@4000: failed to create phy [ 5.060015] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 5.060766] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 5.060781] cfg80211: failed to load regulatory.db [ 5.061200] rockchip-pm rockchip-suspend: not set pwm-regulator-config [ 5.062177] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 405; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '16:18:18', on 'Mar 31 2023'. [ 5.062773] Mali: [ 5.062776] Mali device driver loaded [ 5.063676] rockchip-usb2phy fd5d8000.syscon:usb2-phy@8000: failed to create phy [ 5.064196] rockchip-usb2phy fd5dc000.syscon:usb2-phy@c000: failed to create phy [ 5.064689] rockchip-usb2phy fd5d4000.syscon:usb2-phy@4000: failed to create phy [ 5.068983] ret 1024 0 [ 5.069262] ALSA device list: [ 5.069282] #0: rockchip,hdmiin [ 5.069293] #1: rockchip-dp0 [ 5.079162] Freeing unused kernel memory: 7616K [ 5.099568] Run /init as init process Loading, please wait... /dev/console is Ok [ 5.122305] mmc_host mmc1: Bus speed (slot 0) = 148500000Hz (slot req 150000000Hz, actual 148500000HZ div = 0) [ 5.132771] dwmmc_rockchip fe2c0000.mmc: Successfully tuned phase to 209 [ 5.132800] mmc1: new ultra high speed SDR104 SDXC card at address aaaa [ 5.133652] mmcblk1: mmc1:aaaa SN128 119 GiB [ 5.135243] mmcblk1: p1 [ 5.139694] rockchip-usb2phy fd5d8000.syscon:usb2-phy@8000: failed to create phy [ 5.140533] rockchip-usb2phy fd5dc000.syscon:usb2-phy@c000: failed to create phy [ 5.141283] rockchip-usb2phy fd5d4000.syscon:usb2-phy@4000: failed to create phy starting version 237 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. [ 6.790739] rk_hdmirx fdee0000.hdmirx-controller: hdmirx_cancel_cpu_limit_freq freq qos nod add Begin: Will now check root file system ... fsck from util-linux 2.36.1-4309-dirty [/sbin/fsck.ext4 (1) -- /dev/mmcblk0p6] fsck.ext4 -a -C0 /dev/mmcblk0p6 rootfs: clean, 3911/65536 files, 145641/244597 blocks done. [ 7.166407] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... Warning: overlayroot: configuring overlayroot with driver=overlay mode=device opts='dev=PARTLABEL=userdata,fstype=ext4,mkfs=1' per kernel cmdline [ 7.380501] EXT4-fs (mmcblk0p7): recovery complete [ 7.381036] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: (null) Success: overlayroot: configured root with 'device:dev=PARTLABEL=userdata,fstype=ext4,mkfs=1' using overlay per kernel cmdline Warning: Something odd, no /lib/modules/5.10.110 in initramfs. done. mount: /dev: devtmpfs already mounted or mount point busy. mount: /oem: can't find LABEL=oem. mount: /userdata: can't find LABEL=userdata. Starting syslogd: OK Starting klogd: OK Running sysctl: OK /bin/modetest drmModeGetResources failed: Operation not supported Populating /dev using udev: [ 7.807804] udevd[523]: starting version 3.2.10 [ 7.824889] udevd[524]: starting eudev-3.2.10 [ 7.944013] rockchip-csi2-dphy0: No link between dphy and sensor [ 7.944016] rockchip-csi2-dphy0: No link between dphy and sensor [ 7.944082] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[3] get remote terminal sensor failed! [ 7.944092] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed! [ 7.944095] stream_cif_mipi_id0: update sensor info failed -19 [ 7.944100] stream_cif_mipi_id3: update sensor info failed -19 [ 7.944702] rockchip-csi2-dphy0: No link between dphy and sensor [ 7.944739] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[1] get remote terminal sensor failed! [ 7.944750] stream_cif_mipi_id1: update sensor info failed -19 [ 7.944819] rockchip-csi2-dphy0: No link between dphy and sensor [ 7.944841] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[2] get remote terminal sensor failed! [ 7.944847] rkcif_scale_ch2: update sensor info failed -19 [ 7.945049] rockchip-csi2-dphy0: No link between dphy and sensor [ 7.945064] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[2] get remote terminal sensor failed! [ 7.945071] stream_cif_mipi_id2: update sensor info failed -19 [ 7.947545] rockchip-csi2-dphy0: No link between dphy and sensor [ 7.947623] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed! [ 7.947628] rkcif_tools_id0: update sensor info failed -19 [ 7.948246] rockchip-csi2-dphy0: No link between dphy and sensor [ 7.948297] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[3] get remote terminal sensor failed! [ 7.948306] rkcif_scale_ch3: update sensor info failed -19 [ 7.948706] rockchip-csi2-dphy0: No link between dphy and sensor [ 7.948728] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed! [ 7.948732] rkcif_scale_ch0: update sensor info failed -19 [ 7.949663] rockchip-csi2-dphy0: No link between dphy and sensor [ 7.949706] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[2] get remote terminal sensor failed! [ 7.949714] rkcif_tools_id2: update sensor info failed -19 [ 7.951295] rockchip-csi2-dphy0: No link between dphy and sensor [ 7.951331] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[1] get remote terminal sensor failed! [ 7.951336] rkcif_scale_ch1: update sensor info failed -19 [ 7.954115] rockchip-csi2-dphy0: No link between dphy and sensor [ 7.954159] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[1] get remote terminal sensor failed! [ 7.954163] rkcif_tools_id1: update sensor info failed -19 done Initializing random number generator: OK Saving random seed: OK Will now mount all partitions in /etc/fstab Note: Will skip fsck, remove /.skip_fsck to enable Handling /dev/root / ext4 rw,noauto 1 Handling tmpfs /tmp tmpfs mode=1777 0 Handling tmpfs /run tmpfs mode=0755,nosuid,nodev 0 Handling proc /proc proc defaults 0 Handling devtmpfs /dev devtmpfs defaults 0 Handling devpts /dev/pts devpts mode=0620,ptmxmode=0666,gid=5 0 Handling tmpfs /dev/shm tmpfs nosuid,nodev,noexec 0 Handling sysfs /sys sysfs defaults 0 Handling configfs /sys/kernel/config configfs defaults 0 Handling debugfs /sys/kernel/debug debugfs defaults 0 Handling pstore /sys/fs/pstore pstore defaults 0 Handling /dev/block/by-name/oem /oem ext2 defaults 2 Handling /dev/block/by-name/userdata /userdata ext2 defaults 2 Mounting /dev/mmcblk0p7(ext2) on /userdata with -o defaults Log saved to /tmp/mount-all.log Starting system message bus: done Increase the maximum socket receive buffer size to 32MB net.core.rmem_max = 33554432 Increase the total amount of buffer space that can be allocated. The value is in pages. The unit of each page is 4096 bytes:262144 327680 393216 net.ipv4.udp_mem = 262144 327680 393216 Increase the receive packet queue size:2000 net.core.netdev_max_backlog = 2000 Increase the min free kbytes size:88M vm.min_free_kbytes = 90112 vm.dirty_ratio = 10 vm.dirty_background_ratio = 5 /etc/profile.d/sysctlUDPbuffer.sh: line 14: echo: write error: Invalid argument /etc/profile.d/sysctlUDPbuffer.sh: line 15: echo: write error: Invalid argument starting bootanim... Starting bootanim: 825... done. Starting hook: /etc/bootanim.d/gst-bootanim.sh... load wifi modules: [ 9.477807] bcmdhd: loading out-of-tree module taints kernel. [ 9.491348] [dhd] _dhd_module_init: in Dongle Host Driver, version 101.10.361.25 (wlan=r892223-20220929-2) [ 9.491348] /home2/lvsx/project/rk3588_rk/external/rkwifibt/drivers/bcmdhd compiled on Jan 29 2023 at 14:48:27 [ 9.491348] [ 9.491415] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: Enter [ 9.491502] [dhd] dhd_wlan_init_gpio: WL_HOST_WAKE=-1, oob_irq=125, oob_irq_flags=0x4 [ 9.491510] [dhd] dhd_wlan_init_gpio: WL_REG_ON=-1 [ 9.491519] [dhd] STATIC-MSG) dhd_static_buf_init : 101.10.361.25 (wlan=r892223-20220928-2) [ 9.491893] [dhd] STATIC-MSG) dhd_init_wlan_mem : prealloc ok for index 0: 8138752(7948K) [ 9.491908] [dhd] dhd_wifi_platform_load: Enter [ 9.491917] [dhd] Power-up adapter 'DHD generic adapter' [ 9.492032] [dhd] wifi_platform_set_power = 1, delay: 200 msec [ 9.492043] [dhd] ======== PULL WL_REG_ON(-1) HIGH! ======== [ 9.492052] [WLAN_RFKILL]: rockchip_wifi_power: 1 [ 9.492060] [BT_RFKILL]: rfkill_get_bt_power_state: rfkill-bt driver has not Successful initialized [ 9.596437] [WLAN_RFKILL]: wifi turn on power [GPIO20-1] [ 9.903227] [dhd] wifi_platform_bus_enumerate device present 1 [ 9.903242] [dhd] ======== Card detection to detect SDIO card! ======== [ 12.113123] [dhd] failed to power up DHD generic adapter, 0 retry left [ 12.129342] [dhd] wifi_platform_set_power = 0, delay: 0 msec [ 12.129358] [dhd] ======== PULL WL_REG_ON(-1) LOW! ======== [ 12.129365] [WLAN_RFKILL]: rockchip_wifi_power: 0 [ 12.129371] [BT_RFKILL]: rfkill_get_bt_power_state: rfkill-bt driver has not Successful initialized [ 12.129376] wifi power off [ 12.232947] [WLAN_RFKILL]: wifi shut off power [GPIO20-0] [ 12.232990] [dhd] wifi_platform_bus_enumerate device present 0 [ 12.233001] [dhd] ======== Card detection to remove SDIO card! ======== [ 12.233014] [dhd] failed to power up DHD generic adapter, max retry reached** [ 12.233025] [dhd] unregister wifi platform drivers [ 12.233036] [dhd] wifi_platform_bus_enumerate device present 0 [ 12.233045] [dhd] ======== Card detection to remove SDIO card! ======== [ 12.233056] [dhd] STATIC-MSG) dhd_static_buf_exit : Enter [ 12.233328] [dhd] dhd_wlan_deinit_gpio: gpio_free(WL_HOST_WAKE 0) [ 12.233337] [dhd] _dhd_module_init: Failed to load the driver, try cnt 0 [ 12.233357] [dhd] _dhd_module_init: Failed to load driver max retry reached** [ 12.233361] [dhd] _dhd_module_init: Exit err=-19 killall: brcm_patchram_plus1: no process killed sh: line 1: /sys/class/rfkill/rfkill0/state: No such file or directory sh: line 1: /proc/bluetooth/sleep/btwrite: No such file or directory sh: line 1: /sys/class/rfkill/rfkill0/state: No such file or directory sh: line 1: /proc/bluetooth/sleep/btwrite: No such file or directory OK ###AMPAK FW Auto detection patch version = [v1.1 20161117]### FW folder path = /system/etc/firmware port --no2bytes could not be opened, error 2 wl: wl driver adapter not found Starting bluetoothd: OK Starting network: OK Starting seatd: OK Starting dhcpcd... dhcpcd-9.4.1 starting dev: loaded udev DUID 00:01:00:01:2b:94:74:6e:ce:90:6d:3d:be:6c forked to background, child pid 906 [ 32.762500] rockchip_canfd fea60000.can can0: bit-timing not yet defined [ 32.763128] phy_rtl8211f_led_fixup in Starting ntpd: [ 32.784049] hcq : phy_rtl8211e_eee_fixup in [ 32.805205] phy_rtl8211f_led_fixup in [ 32.825904] hcq : phy_rtl8211e_eee_fixup in [ 32.876379] rk_gmac-dwmac fe1b0000.ethernet eth0: PHY [stmmac-0:01] driver [RTL8211F Gigabit Ethernet] (irq=POLL) [ 32.882745] dwmac4: Master AXI performs any burst length [ 32.882795] rk_gmac-dwmac fe1b0000.ethernet eth0: No Safety Features support found [ 32.882820] rk_gmac-dwmac fe1b0000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 32.883198] rk_gmac-dwmac fe1b0000.ethernet eth0: registered PTP clock [ 32.883585] rk_gmac-dwmac fe1b0000.ethernet eth0: configuring for phy/rgmii-rxid link mode [ 32.913443] 8021q: adding VLAN 0 to HW filter on device eth0 [ 32.914214] phy_rtl8211f_led_fixup in [ 32.935167] hcq : phy_rtl8211e_eee_fixup in [ 32.956565] phy_rtl8211f_led_fixup in [ 32.977801] hcq : phy_rtl8211e_eee_fixup in [ 33.026263] rk_gmac-dwmac fe1c0000.ethernet eth1: PHY [stmmac-1:01] driver [RTL8211F Gigabit Ethernet] (irq=POLL) [ 33.030211] dwmac4: Master AXI performs any burst length [ 33.030345] rk_gmac-dwmac fe1c0000.ethernet eth1: No Safety Features support found [ 33.030406] rk_gmac-dwmac fe1c0000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported [ 33.031269] rk_gmac-dwmac fe1c0000.ethernet eth1: registered PTP clock [ 33.032271] rk_gmac-dwmac fe1c0000.ethernet eth1: configuring for phy/rgmii-rxid link mode [ 33.060009] 8021q: adding VLAN 0 to HW filter on device eth1 OK Increase the maximum socket receive buffer size to 32MB net.core.rmem_max = 33554432 Increase the total amount of buffer space that can be allocated. The value is in pages. The unit of each page is 4096 bytes:262144 327680 393216 net.ipv4.udp_mem = 262144 327680 393216 Increase the receive packet queue size:2000 net.core.netdev_max_backlog = 2000 Increase the min free kbytes size:88M vm.min_free_kbytes = 90112 vm.dirty_ratio = 10 vm.dirty_background_ratio = 5 /etc/profile.d/sysctlUDPbuffer.sh: line 14: echo: write error: Invalid argument Starting dropbear sshd: OK Starting pulseaudio: OK Increase the maximum socket receive buffer size to 32MB net.core.rmem_max = 33554432 Increase the total amount of buffer space that can be allocated. The value is in pages. The unit of each page is 4096 bytes:262144 327680 393216 net.ipv4.udp_mem = 262144 327680 393216 Increase the receive packet queue size:2000 net.core.netdev_max_backlog = 2000 Increase the min free kbytes size:88M vm.min_free_kbytes = 90112 vm.dirty_ratio = 10 vm.dirty_background_ratio = 5 W: [pulseaudio] main.c: This program is not intended to be run as root (unless --system is specified). /etc/profile.d/sysctlUDPbuffer.sh: line 14: echo: write error: Invalid argument --------------------start----------------- /etc/init.d/S51start: line 5: /mnt/cfg/start.sh: No such file or directory Increase the maximum socket receive buffer size to 32MB net.core.rmem_max = 33554432 Increase the total amount of buffer space that can be allocated. The value is in pages. The unit of each page is 4096 bytes:262144 327680 393216 net.ipv4.udp_mem = 262144 327680 393216 Increase the receive packet queue size:2000 net.core.netdev_max_backlog = 2000 Increase the min free kbytes size:88M vm.min_free_kbytes = 90112 vm.dirty_ratio = 10 vm.dirty_background_ratio = 5 sh: echo: write error: Invalid argument sh: echo: write error: Invalid argument